Fda-Eua Approved Molecular Pcr Sars-Cov2

Product Overview

The Q-Plex™ SARS-CoV-2 Human IgG (4-plex) Multiplex ELISA Kit is a qualitative chemiluminescent assay (ELISA) allowing concurrent measurement of human IgG antibodies to SARS-CoV-2 S1 and SARS-CoV-2 S2 proteins in serum and plasma samples. It has been authorized by FDA under a EUA for use by high complexity CLIA labs. Sensitive, reproducible, and convenient 96-well format requiring low sample volumes. Requires the Q-View™ Imaging System for analysis.

Assay Principle

The Q-Plex™ SARS-CoV-2 Human IgG (4-Plex) multiplex assay is a qualitative enzyme-linked immunosorbent assay that detects IgG antibodies to SARS-CoV-2 in human serum or plasma. SARS-CoV-2 is the novel coronavirus that causes COVID-19. The SARS-CoV-2 virus has several structural proteins including two spike proteins, S1 and S2. When an individual is infected with the SARS-CoV-2 virus, their immune system produces antibodies to these viral proteins. The typical immune response produces detectable antibody levels ~8-10 days following the onset of symptoms.

The Q-Plex SARS-CoV-2 Human IgG Quantitative (4-Plex) Multiplex ELISA detects IgG antibodies to both the S1 and S2 spike proteins present in a blood sample. If antibodies are detected, the result will be considered positive. If antibodies are not detected, the result will be considered negative. The assay only detects IgG antibodies, not other classes of antibodies such as IgM or IgA.

The multiplex assay allows for simultaneous indirect ELISA on the following four printed spots:;_x000D_

_x000D_
1. SARS-CoV-2 Spike Glycoprotein (S1), a recombinant antigen which contains amino acids 1-674 of subunit 1. Spike S1 is expressed in mammalian HEK293 cells with a Sheep Fc-Tag.
_x000D_
2. SARS-CoV-2 Spike Glycoprotein (S2) is a recombinant antigen which contains the Spike subunit 2 protein, amino acids 685-1211. Spike S2 is expressed in mammalian HEK293 cells with a Sheep Fc-Tag.
_x000D_
3. Sheep Fc is a negative control to ensure no cross-reactivity occurs between human IgGs in the sample and the Fc-Tag on the SARS-Cov-2 Spike proteins.
_x000D_
4. Anti-Human IgG is a positive control to ensure the kit performs and the IFU was followed correctly.
_x000D_

Assay Validation

The Q-Plex™ SARS-CoV-2 Human IgG (4-Plex) ELISA tests for IgG antibodies to either the SARS-CoV-2 S1 protein or the SARS-CoV-2 S2 protein. Our validation studies identified measurable improvement in clinical performance when results from the S1 and S2 assays are considered together rather than single assays (see assay validation data below). Quansys recommends that a sample should only be considered positive for the presence of SARS-CoV-2 reactive IgGs when antibodies reactive to both S1 and S2 are detected.

Negative samples, collected prior to August 2019, and known positive samples collected from individuals who tested positive for COVID-19 on a molecular test at least 14 days prior to sample collection were used to determine clinical sensitivity and specificity.

Evaluating the S1 and S2 simultaneously allows for greater clinical sensitivity and specificity.

Kit Components

Each kit contains a 96-well plate, featuring the relevant biomarker panel in each well, and all reagents required to perform testing.

Reagents include:

Wash Buffer Concentrate (20X): Liquid, 50 mL/vial of a concentrated solution of buffered surfactant;_x000D_Sample Diluent (2X): Liquid, 10 mL/vial of a concentrated buffered protein solution with preservatives;_x000D_Detection Mix: Liquid, 6 mL/vial of biotinylated antibodies in a buffered protein solution with preservatives;_x000D_Calibrators (High, Low, Negative): Lyophilized, human serum diluted in a buffered protein base;_x000D_Streptavidin-HRP (1X): Liquid, 6 mL/vial of streptavidin-conjugated horseradish peroxidase;_x000D_Substrate A: Liquid, 3 mL/vial of peroxide solution;_x000D_Substrate B+: Liquid, 3 mL/vial of luminol solution;_x000D_Plate Seals (3): Adhesive strips

Kit Processing

The Multiplex assays require the use of the Q-View™ software to read and interpret the test results. A fully-functional, free trial version of the software is available to download, install, and use to analyze your first kit (s). At the end of the trial period, a purchased license is required to continue the use of the Q-View software.

Q-Plex arrays are developed and optimized to work with Q-View imagers. We do not guarantee the results obtained from other imagers because not all imagers are compatible with Q-Plex arrays.